RH45E32XW_dm-en-01.jpg

The T-REX 450 has been the ideal choice for entry level R/C helicopters. To cater to the beginner enthusiasts and solve the problem of assembly and adjustment, Align introduces the T-REX 450LP ARTF (Almost Ready to Fly). Completed with an Align A10 transmitter and newly released MiniGRS flybarless system, you are now able to experience RC Helicopter flight.

The helicopter utilizes a DFC rotor head, paired with the MiniGRS flybarless system optimized for the T-REX 450LP flight characteristics. Without any adjustment or tuning, this RC Helicopter combo from Align provides optimal stability suitable for pilots of all levels.

Equipped with new digital high voltage (HV) servos DS450 and DS455, supporting 8.4 volts to provide optimal speed and torque performance. Paired with the new RCE-BL45P ESC, with adjustable 5~8.4V BEC function to profoundly improve flight performance.

ALIGN A10 is AFHDS (Automatic Frequency Hopping Digital System) is a 10 channel 2.4GHz transmitter. The A10 is an ergonomic design to provide a comfortable feel with smoother control. The Align A10 is a full function transmitter offering helicopter/aircraft /multicopter modes. A simple control interface allows for easy setup.

With the addition of the brand new A10 transmitter and MiniGRS, the T-REX 450LP ARTF pushes past the performance limitation of a flybar helicopter, improving both stability and 3D performance, at a down to earth price level.

Image

Included is the A10 Transmitter with Automatic Frequency Hopping Digital System, AFHDS is a highly developed remote signal transmission system, providing long range, minimizing interference, with lower power consumption.

Image

Easly charge the T-REX 450LP ARTF battery with the included RCC-3SX Align Balance Charger for 2S 7.4V and 3S 11.1V lipo batteries.

Image

Included is an Align 3S 11.1V Lipo battery. When ordering your T-REX 450LP ARTF we suggest ordering an additional battery.

The T-REX 450LP ARTF assembly is simple and quick by following the instructional video. You will be ready to fly before the battery is full charged.

en_quickfinder960.gif
Standard Equipment
  • T-REX 450LP ARTF Kit x 1
  • A10 Transmitter x 1
  • RCE-BL45P ESC x 1
  • 460MX Brushless motor (3200KV/2222) x 1
  • DS450 HV Brushless Servo x 3 Freq: 200hz
  • DS455 HV Brushless Servo x 1 Pulse: 1520µs / Freq: 333hz
  • MiniGRS Flybarless System x 1
  • Balance Charger RCC-3SX x 1
  • 3S1P 11.1V 2200mAh/30C Battery x 1
450LP Specifications
  • Length: 705mm - 27.76In
  • Height: 205mm - 8.07In
  • Width: 110mm - 4.33In
  • Main Blade Length: 325mm - 12.80In
  • Main Rotor Diameter: 734mm - 28.90In
  • Tail Rotor Diameter: 171mm - 6.73In
  • Motor Drive Gear: 11T
  • Main Drive Gear: 121T
  • Autorotation Tail Drive Gear: 106T
  • Tail Drive Gear: 26T
  • Drive Gear Ratio: 11 : 1 : 4.07
  • Weight (w/o battery): 730g - 1.60Lbs
A10 Specifications
  • 10-Channel Transmitter
  • Modes: Helicopter/Airplane/Multicopter
  • Frequency Range: 2.408 ~ 2.475 GHz
  • Power: No Higher Than 20dBM (EU)
  • System: 2.4 AFHDS 2A
  • Voltage Range: 4.0V ~ 6.0V DC
  • Receiving Distance: Line of Site <1000M
  • Low Voltage Warning: < 4.2V
  • Weight: (no batteries) 487g - 1.07Lbs
  • Size: 275x187x102mm - 10.8x7.4x4In
MiniGRS Flybarless Specifications
  • Operating Voltage Range: DC 3.5~8.4V
  • Operating Current Consumption: <100mA @4.8V
  • Rotational Detection Rate: ±300°/sec
  • Rudder yaw detection rate: ±600°/sec
  • Sensor Resolution: 12 BIT
  • Swashplate Support: 120° CCPM Swashplate
  • Mode Support: T-REX250, T-REX450, T-REX470, T-REX500
  • Receiver Support: ALIGN A10(A.BUS), Futaba S-FHSS, DSM2/DSMX
  • Operating Temperature: -20℃ ~ 65℃
  • Operating Humidity: 0% ~ 95%
  • Comply with RoHS
  • Size: 37.6x22.4x13mm - 1.5x0.9x0.5In
A6B Receiver Specifications
  • Channel: 14 Channels
  • RX Sensitivity: -105dBm
  • RF Range: 2.408 ~ 2.475 GHz
  • System Mode: 2.4G system AFHDS 2A
  • Power: 4.0 ~ 8.4V
  • Transmit Distance: Line of Site <1000M
  • Dimension: 46.7x25.5x13.6mm - 1.8x1x0.5In
Balance Charger RCC-3SX Specifications
  • Input Voltage: AC 100V~240V(50/60Hz)
  • Output Voltage: 2cell DC 7.4V / 3cell DC 11.1V
  • Supported Battery Type: Li-polymer/Li-ion
  • Charging Method: CC/CV
  • Charging Current: 2A
  • Size: 123x74.3x32mm - 4.8x2.9x1.3In
  • Weight: 260g - 0.57Lbs
Battery Specifications
  • Output: 11.1V 2200mAh 24.4Wh (3S1P)
  • Supports 5C Charging
  • Dimension: 104x36x22mm - 4.1x1.4x0.9In
  • Weight: 165g - 0.36Lbs
  • 14AWG Heat-Resistant Silicone Wire. Heat Resistance: 200 ° C / Current withstand: 50A
Equipment Recommended for Assembly
  • Digital Pitch Gauge Part # HET80001
  • Swashplate Leveler x 1 Part # H45191
Suggest Extra Equipment
  • 3S1P 11.1V 2200mAh/30C Lipo Part # HBP22003
  • 450L Battery Mount Tray Part # H45B011XX
  • Hook and Loop Tape 450 Part # HS1240
  • Hook and Loop Fastening Strap Part # HS1265
  • Radio Strap (Red or Yellow) Part # HOS00011 or HOS00012
450LP ARTF Quick Start
450LP ARTF Quick Start
450LP ARTF Manual
450LP ARTF Manual
A10 Transmitter Manual
A10 Transmitter Manual
MiniGRS Manual
MiniGRS Manual
A10 FMS Simulator
A10 FMS Simulator
authorized_align_dealer.png
© 2017 Enterprise Hobby. All Rights Reserved. Designed By dXb Development

Search